Honda Civic/Acura Integra

since 1994 of release

Repair and car operation

Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
- Engine
   + engine Repair without extraction from the car - the Civic models
   - Engine repair without extraction from the car - the Integra models
      General information
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of a cover of a head of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft
      VTEC systems - the general information and check of a condition of components
      Removal, check of a condition and installation of camshafts and assembly of yokes
      Replacement of klapanny springs with plates and maslootrazhatelny caps
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Flywheel replacement / driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit
   + General and major maintenance of the engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

Removal, check of a condition and installation of the oil pump

Removal

PERFORMANCE ORDER

1. Remove a belt of a drive of GRM (see. Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM).
2. Remove the pallet of a case of the engine (see. Removal and installation of the pallet of a case of the engine).
3. Disconnect assembly of a maslozabornik with the mesh filter and a tube from the bridge of covers of radical bearings and the pump case.

4. Turn out fixing bolts and remove the oil pump from the engine (see an accompanying illustration).

5. Turn out fixing screws and remove from the pump a cover (see an accompanying illustration).

Not to break a shlitsa in heads of fixing screws their easing it is better to make by means of a shock screw-driver.

Check

PERFORMANCE ORDER

1. Measure size of working gaps of gear wheels of the pump (see illustrations 1a, 1b, 1c ). Compare results of measurements to requirements of Specifications. If the size of gaps falls outside the limits admissible values, replace the pump.
2. Turn out a stopper of the reduktsionny valve and take from a nest in the pump case a spring and a plunzher of the valve. Check a spring on existence of deformations, and a plunzher – on existence of scratches and задиров. Defective components are subject to replacement.
3. Establish gear wheels in the case of the pump and fill cavities between teeths technical vaseline.
4. Grease screws of fastening of a cover of the pump with anti-taking hermetic. Establish a cover, screw screws and tighten them with demanded effort. Establish in the pump case a spring and a plunzher of the reduktsionny valve. Having replaced a sealing washer, screw a stopper and strongly tighten it.

Installation

PERFORMANCE ORDER

1. Slightly grease with anaerobny hermetic a surface of the case of the pump interfaced to the block and enclosed in a flute in the case a new sealing ring. Establish the pump on the block and with demanded effort tighten fixing bolts.
2. Establish into place assembly of a maslozabornik, having tightened fixing bolts with demanded effort (do not forget to replace sealing laying).
3. Establish the case pallet (see. Removal and installation of the pallet of a case of the engine).
4. Further installation is made as it should be, the return to a dismantle order. In summary do not forget to fill in in the engine engine oil and to fill cooling system (see. Head Routine maintenance).
5. Start the engine and check its existence of signs of leaks.