Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability with basic plugs
   Removal and installation of the top control lever of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of a rotary fist and stupichny assembly
   Removal and installation of assembly of a forward nave with the wheel bearing
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of a bar of the back stabilizer of cross-section stability with basic plugs
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




94e743ed
Консультация юриста

Suspension bracket and steering

General information

Forward suspension bracket completely independent with top and bottom levers, shock-absorbers with screw springs and the stabilizer of cross-section stability (see illustrations below).

In an independent back suspension bracket longitudinal levers, the top and bottom levers and assemblies of shock-absorbers with screw springs (see illustrations below) are used.

All models are completed with the reechny steering mechanism. On some models hydraulic strengthening of a wheel is provided. In system of hydrostrengthening of a wheel (PAS) the steering pump connected to a case of the reechny mechanism by means of flexible hydraulic hoses is used given to rotation from the engine.

Often in the course of service of components of a suspension bracket it is necessary to face fixture resistant to an otdavaniye.“ By Prikipaniye” elements of fixture it is connected with that they are constantly subject to external influences, are in contact to water, dirt, a soot and other promoting development of corrosion by substances. For the purpose of simplification of procedure of an otdavaniye of its such "become attached" fixture it is necessary to impregnate with plentiful amount of getting oil beforehand. Cleaning of open carving parts of fixture by a rigid wire brush also promotes simplification of an otdavaniye of prirzhavevshy nuts. Sometimes, in especially hard cases, for an otpuskaniye "become attached" bolts/nuts it is possible to use a drift. The drift rests against the region of a shliyets of a nut/head of a bolt and sharp blows are struck to its opposite end with a hammer. Watch that the drift did not break, try not to damage in inexact blows a carving. Quite effective way is also warming up of fixture not giving in to an otdavaniye and a surface of a component surrounding it a torch of a blowtorch or a gas torch though originators of this Management and do not recommend to resort without extreme need to such technology in view of its potential danger connected with possibility of ignition and risk of receiving burns. Different extended collars and trumpet nozzles are intended for increase in a torque at an otpuskaniye of fixture on them, however remember that it is not necessary to use such intensifying adaptations complete with the drive equipped with "graggers" – the risk of failure of the ratchet mechanism is too great. Sometimes the nut/bolt starts to give in after previously slightly will be tightened clockwise. All fixture, which otpuskaniye demanded application of extraordinary measures at assembly is subject to replacement!

After an otdavaniye attentively check a condition of fixture and in case of need make its replacement with elements of the same standard size. At assembly tighten fixture of components of a suspension bracket and a steering it is strict with demanded effort.


At all do not undertake attempts of a rikhtovka of the deformed components of a suspension bracket and a steering – replace defective details!

As procedures of service of components of a suspension bracket are carried out under the car, it is necessary to take care in advance of possibilities of lifting of a vehicle and its fixing in the lifted situation (prepare reliable a jack and props).

At all do not perform any works under the car, fixed in the lifted situation only by means of a jack!

Components of a forward suspension bracket

1 — the Steering mechanism
2 — the Collar of the plug of the bottom control lever
3 — Nizhny a control lever

4 — Dempfernaya a fork
5 — the Rotary fist
6 — shock-absorber Assembly with a screw spring

Components of a back suspension bracket

1 — shock-absorber Assembly with a screw spring
2 — the Top lever
3 — Nizhny the lever

4 — the Compensatory lever
5 — the Longitudinal lever