Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ Cцепление and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability with basic plugs
   Removal and installation of the top control lever of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of a rotary fist and stupichny assembly
   Removal and installation of assembly of a forward nave with the wheel bearing
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of a bar of the back stabilizer of cross-section stability with basic plugs
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment





Replacement of the shock-absorber or screw spring of rack-mount assembly of a forward suspension bracket

 PERFORMANCE ORDER

1. Remove amortizatorny assembly from the car (see. Removal and installation of assembly of the forward shock-absorber with a screw spring or Removal and installation of assembly of the back shock-absorber with a screw spring).
2. Check the shock-absorber on existence of signs of leaks, dents, cracks and other mechanical damages. Examine a screw spring on existence of chips, cracks, prosedaniye signs, and rubber pillows of its support on existence of signs of hardening and material aging. In Honda company service centers always it is possible to get shock-absorbers assembled with screw springs on an exchange basis that allows to reduce temporary and monetary expenses essentially. In view of told before starting shock-absorber dismantling for the purpose of carrying out its major maintenance carry out marketing, having been defined in the prices for replaceable components and having compared them to costs of acquisition of the restored assembly.

Removal of a screw spring from amortizatorny assembly is connected with potential danger and should be made only with use of the high-quality special tool.


3. Clamp shock-absorber assembly in a vice with soft sponges (not too strongly).
4. Mark the provision of the basis of a support in relation to a spring (if the spring is replaced, in relation to dempferny assembly).

5. Following instructions of manufacturers, establish the tool for a szhimaniye of a screw spring. Tightening nuts on tool hairpins (see an accompanying illustration), compress a spring so completely to unload the support basis.

6. Remove a protective cap and give самоконтрящуюся a nut (see an accompanying illustration), holding a damper rod from a provorachivaniye a prutkovy key. Remove from the shock-absorber components of the top support, having spread out them on a pure surface it is strict as an arrangement on assembly.

7. Carefully remove from assembly the compressed screw spring and clean it in a safe place.

Do not develop the compressed spring end faces to itself!


8. Remove from a damper rod the remained components and spread out them on a workbench (as installation on assembly).
9. Rearrange on new dempferny assembly the return buffer with the plate, a dustproof casing and its plate. Extend a rod from a damper for all length of its course and pass it through established components.
10. Accurately put on assembly the compressed screw spring. Track correctness of landing of the bottom end face of a spring in the saddle.
11. Establish a rubber pillow of a saddle of a spring, the plug of a support of a rod the basis of a support of assembly, a washer of a fixing nut and new самоконтрящуюся a nut. Before tightening a nut track correctness of combination of the labels put in the course of dismantle.
12. Holding a rod from a provorachivaniye a prutkovy key, tighten самоконтрящуюся a nut with demanded effort. Release the tool for compression of a spring and remove it from assembly. Establish a protective cap.
13. Get assembly on the regular place and establish on the car (see. Removal and installation of assembly of the forward shock-absorber with a screw spring or Removal and installation of assembly of the back shock-absorber with a screw spring).