Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability with basic plugs
   Removal and installation of the top control lever of a forward suspension bracket
   Removal and installation of the bottom control lever of a forward suspension bracket
   Removal and installation of a rotary fist and stupichny assembly
   Removal and installation of assembly of a forward nave with the wheel bearing
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of a bar of the back stabilizer of cross-section stability with basic plugs
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




94e743ed soaptoday

Removal and installation of a rotary fist and stupichny assembly

Removal

 PERFORMANCE ORDER

1. Remove a rim cap. Weaken a stupichny nut (see an accompanying illustration). Weaken nuts of fastening of a wheel, then поддомкратьте a front of the car and establish it on props. Remove a wheel. Unscrew a stupichny nut.

2. Liberate a flexible brake hose from an arm on assembly of a rotary fist. To Otboltita a support of the brake mechanism also tie up it a wire to a screw spring. Remove also anchor bracket of a support and a brake disk (see. Head Brake system).
3. Disconnect from a rotary fist a tip of steering draft (see. Removal and installation of tips of steering drafts).
4. Separate the bottom lever of a suspension bracket from a spherical support in the lower part of a rotary fist (see. Removal and installation of the bottom control lever of a forward suspension bracket).
5. Separate the top end of a fist from a spherical support of the top lever of a suspension bracket.
6. Accurately delay fist assembly with a nave outside, having removed it from a pin of a power shaft. In case of need knock on a pin end face with a hammer with soft brisk for the purpose of its liberation from a nave. Tie up assembly of a power shaft by a wire in order to avoid damage of the internal CV JOINT.

Installation

 PERFORMANCE ORDER

1. Slightly grease with special greasing of a shlitsa of an external pin of a power shaft. Pass a pin through an opening in a nave, at the same time filling on a regular place a rotary fist.
2. Connect the top part of a fist to a spherical support of the top lever of a suspension bracket (see. Removal and installation of the top control lever of a forward suspension bracket). Tighten a nut of a spherical finger with demanded effort.
3. Connect a spherical support in the lower part of a fist to the bottom lever of a suspension bracket (see. Removal and installation of the bottom control lever of a forward suspension bracket).
4. Establish to the place of a brake disk, an anchor bracket and a support (see. Head Brake system).
5. Screw on a pin of a power shaft a stupichny nut and strongly tighten it.
6. Establish a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see. Specifications to Head Routine maintenance).
7. Tighten a stupichny nut with demanded effort.