Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
- Engine
   + engine Repair without extraction from the car - the Civic models
   + engine Repair without extraction from the car - the Integra models
   - General and major maintenance of the engine
      General information
      Check of pressure of oil
      Check of kompressionny pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal from the car of the power unit - preparation and precautionary measures
      Removal and engine installation
      Alternative versions of schemes of regenerative repair of the engine
      Order of dismantling of the engine by its preparation for major maintenance
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal of shatunno-piston assemblies
      Removal of a cranked shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of shatunno-piston group
      Check of a condition of a cranked shaft
      Check of a condition and selection of loose leaves of radical and shatunny bearings of a cranked shaft
      Engine assembly order
      Installation of piston rings
      Installation of a cranked shaft and check of working gaps of radical bearings
      Replacement of a back epiploon of a cranked shaft
      Installation of shatunno-piston assemblies and check of size of working gaps in shatunny bearings of a cranked shaft
      Trial start and engine running in after major maintenance
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




94e743ed

Replacement of a back epiploon of a cranked shaft

 PERFORMANCE ORDER

Before приболчивать to the engine the holder with the new epiploon established in it, establish into place a cranked shaft and covers of radical bearings.


1. Measure regular depth of landing of an old epiploon in a nest of the holder, then lay a plate of the holder edges on pair of wooden blocks of equal height and by means of a suitable drift and a hammer beat out an old epiploon from the nest (see an accompanying illustration). Try not to damage nest walls.

2. Carefully wipe the holder, then grease external edge of a new epiploon with pure impellent oil. The epiploon should be planted in a nest strictly perpendicularly therefore it is not recommended to make a zabivaniye it in the holder a hammer. In the absence of access to a press it is possible to fill an epiploon in a nest by means of a big vice with soft sponges – thus the holder with an epiploon should be clamped between two flat wooden whetstones providing uniform distribution of loading on all area of a face surface of an epiploon. Hammer use, however a zastukivaniye is as a last resort allowed should be made through flat wooden whetstone (see an accompanying illustration). Act slowly, watching that there was no distortion.

3. With the help щупа lezviyny type measure a gap between an epiploon and the holder. The gap should have equal size on all perimeter of the holder and not fall outside the limits a range 0.51÷0.76 mm.

4. Apply a thin film RTV hermetic on all edge of the holder.
5. Before putting on assembly of the holder with an epiploon a pin of a cranked shaft, grease epiploon sponges with universal greasing. Do not forget to replace sealing laying of the holder.

Before installation both surfaces of laying it is necessary to grease with RTV hermetic also.


6. Having planted the holder closely to the block, by hand acquire bolts of its fastening, make sure of correctness of installation of the holder, then tighten bolts with demanded effort (see. Specifications to Parts engine Repair without extraction from the car - the Civic models and engine Repair without extraction from the car - the Integra models of the present Chapter). Cut laying edge aflush with an interfaced surface of the pallet of a case (try not to scratch the last).