Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
- Cooling and heating systems
Specifications
Antifreeze - general information
Check of serviceability of functioning and thermostat replacement
Check of a condition of the fan (ов) systems of cooling and chain of its inclusion, fan replacement (ов)
Removal and installation of a radiator and broad tank of system of cooling
Removal and installation of a maslookhladitel
Check of a condition of the water pump
Replacement of the water pump
Check of serviceability of functioning and replacement of the block of the sensor of a measuring instrument of temperature of cooling liquid
Check of serviceability of functioning of the driving electromotor of the fan of a heater and condition of components of its electric chain, replacement of components
Removal and installation of the electromotor of a drive of the fan of a heater
Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of a driving cable
Replacement of the heat exchanger of a heater
Check of serviceability of functioning and service of systems of heating and air conditioning
Check of an electric chain of the coupling of coupling of the To/in compressor
Removal and receiver dehumidifier installation To/in
Removal and To/in compressor installation
Removal and To/in condenser installation
Removal and To/in evaporator installation with the broad valve
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of a driving cable
|
|
Cars considered in the real Management are equipped with system of additional safety of SRS which is better known as a safety cushion. Before performing any works near assembly of a pillow or a steering column, without fail disconnect system in order to avoid receiving traumas as a result of its casual operation (see. Head Onboard electric equipment). |
|
|
1. Disconnect a negative wire from the battery. Disconnect a safety cushion (see. Head Onboard electric equipment).
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
2. Remove the bottom section of furnish of the central console (see. Head Body).
3. Remove a stereosystem (see. Head Onboard electric equipment).
|
|
4. Turn out screws of fastening of the deflector of an air line of the central console, take the deflector and give four screws of fastening of assembly of the control panel functioning of the heater/conditioner of air (see an accompanying illustration). |
|
|
5. Take assembly of management and disunite the socket of its electroconducting. Disconnect a cable of management of mixing of air submitted to salon from a control lever (see an accompanying illustration). |
6. Installation is made upside-down.
7. Start the engine and check an isravnost of functioning of systems of heating and air conditioning. |
|
Adjustment Cable of management of mixing of air submitted to salon Civic models
|
|
1. For adjustment of a driving cable disconnect it from the executive lever of the valve of a heater in an impellent compartment. Disconnect a cable from the lever of mixing of air of assembly of management under the dashboard in car salon.
2. Transfer a control lever in temperature to the provision of the maximum cooling (COOL MOVE), then accurately pull for a cover of a cable and close a zaslonka, having tracked, that all weak point a cable appeared is chosen.
3. Holding a control lever air mixing wrung out against the stop, latch a driving cable in a clamp clip.
4. In an impellent compartment transfer the executive lever of the valve to completely closed position and connect a cable. Without releasing the lever, choose a cable weak point, having pulled for its cover, then establish fixing clip. |
|
Integra models
|
|
1. Liberate a driving cable from a clip of a clamp of a control lever.
2. Transfer a control lever in temperature to position of the maximum intensity of heating (HEAT MOVE), then turn a control lever mixing of air and connect a cable.
3. Delay a cable cover back from a tip, having chosen all weak point of a cable, then fix a cable a clip. |
|
Driving cable of the valve of a heater
|
|
1. Disconnect a cable from the valve lever in an impellent compartment. Disconnect a cable of management of air mixing from a control lever under the dashboard.
2. Transfer a control lever in temperature to position of the maximum intensity of heating (HEAT MOVE), turn the handle to a cable and fix the last a clip. Pressing a cable tip to an emphasis, latch in a clip a cable of management of air mixing.
3. In an impellent compartment transfer the executive lever of the valve to completely closed position and connect a cable. Without releasing the lever, choose a cable weak point, having pulled for its cover, then establish fixing clip. |
|
|
|
