Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of assemblies of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of a latch, cylinder of the lock and emphasis of a door of a back
   Removal, installation and adjustment of a door of a back
   Removal and installation of a latch, cylinder of the lock and emphasis of a cover of a luggage compartment
   Removal, installation and adjustment of a cover of a luggage compartment
   Driving cables of an otpuskaniye of locks of covers of a luggage compartment and hatch of a jellied mouth of a fuel tank
   Removal and installation of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of latches and cylinders of locks and external and internal handles of doors
   Removal and installation of door glasses
   Removal and installation of a regulator of a window regulator
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and dashboard installation
   Removal and installation of a casing of a steering column
   Removal and installation of an instrument guard
   Removal and installation of a forward fairing
   Removal and installation of seats
   + Control body sizes
+ Onboard electric equipment




94e743ed

Removal and installation of assemblies of forward and back bumpers

Front bumper

 PERFORMANCE ORDER

1. Cock the parking brake, поддомкратьте the car and establish it on props.
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


3a. Turn out the central screws of fastening of the antispray screen.

3b. Under the car turn out screws of fastening of bottom edges of an overlay of a bumper (see accompanying illustrations).

4. Operating through arches of forward wheels, turn out screws of an overlay of a bumper to loker (see an accompanying illustration).

5. Turn out bolts of fastening of an overlay of a bumper to the car chassis (see an accompanying illustration).

6. Give screws (or, on some models, take plastic clamps) fastenings of the upper edge of a slip (see an accompanying illustration) and remove the last from the car.


Plastic clamps are taken by a poddevaniye by the suitable tool after preliminary liberation of the central pin.


7. Disunite sockets of the electroconducting disturbing to removal of a bumper. In case of need remove the knitsa established since both ends of a bumper, then turn out four bolts and remove a bumper from the car.
8. Installation is made upside-down.

Rear bumper

 PERFORMANCE ORDER

1. Cock the parking brake, поддомкратьте the car and establish it on props.

2. Under the car take plastic clamps and turn out screws of fastening of bottom edge of an overlay of a rear bumper (see an accompanying illustration).

3. Turn out screws of fastening of a slip to arches of back wheels (see an accompanying illustration).

4a. Open a cover a back luggage carrier/door.

4b. From within a luggage compartment give screws and nuts of fastening of the upper edges of an overlay of a bumper (see accompanying illustrations). Remove an overlay of a bumper from the car.

5. For removal of a bearing part of a bumper drill rivets of fastening of penoplastovy isolation, then give bolts and remove bumper assembly from the car.
6. Installation is made upside-down.