Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
- Control systems of the engine
Specifications
System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions
Removal and installation RSM/ESM
Check of serviceability of a condition and replacement of the sensor of provision of a butterfly valve (TPS)
Check of serviceability of a condition and replacement of the sensor of absolute pressure in the pipeline (MAR)
Check of serviceability of a condition and replacement of the sensor of temperature of soaked-up air (IAT)
Check of serviceability of a condition and replacement of the sensor of temperature of cooling liquid of the engine (eats)
Check of serviceability of a condition and replacement of the sensor of VMT/provision of cranked shaft/position of pistons in cylinders of the engine (TDC/CKP/CYP)
Check of serviceability of a condition and replacement of the sensor of fluctuations of a cranked shaft (CKF)
Check of serviceability of a condition and replacement of the detector of control of electric loadings (ELD)
Check of serviceability of a condition and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
Check of serviceability of a condition and replacement of the oxygen sensor (l-probe)
Check of serviceability of a condition and replacement of the sensor of a detonation
Check of serviceability of a condition and replacement of the sensor of speed of movement of the car (VSS)
System of stabilization of turns of idling - the general information, check of a condition and IAC valve replacement
Check of serviceability of a condition and replacement of the thermosensitive valve of turns of fast idling (FIT)
System of a perepuskaniye of soaked-up air - the general information, check of a condition and replacement of a diaphragm of the IAB valve
System of operated ventilation of a case (PCV)
System of a retsirkulyatsiya of the fulfilled gases (EGR) - the general information, check of a condition and replacement of components
System of catching of fuel evaporations (EVAP) - the general information, check of a condition and replacement of components
The catalytic converter - the general information, check of a condition and replacement
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Check of serviceability of a condition and replacement of the sensor of temperature of cooling liquid of the engine (eats) Check
|
|
1. The eats sensor represents a termistor (the resistor which resistance changes with temperature change). Change of resistance of the sensor makes direct impact on amplitude of the signal which is given out by the sensor on ESM/RSM. Thus with temperature REDUCTION resistance of the sensor INCREASES, and on the contrary. At existence in memory ESM/RSM of the corresponding code of malfunction (see. System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions) should be checked a condition of a chain eats and if electroconducting as it should be, to replace the sensor.
|
|
2. Check of the sensor is made by measurement of its resistance (see an accompanying illustration) in a cold condition (10°С÷27°С). then start the engine and warm up it to normal working temperature. Resistance of the sensor should fall. |
3. Measure supply voltage on the plug of a red-black wire of the socket of electroconducting of the sensor at the included ignition (do not start the engine). The result of measurement should make about 5.0 In, otherwise check a wire on break on a site from the sensor to ESM/RSM. |
|
Replacement
|
|
Before starting procedure performance, wait complete cooling of the engine. |
|
|
|
1. Before installation of the new sensor it is necessary to wind its carving part with a teflon sealing tape (tape FUM).
2. Wring out a lock uvula, then accurately turn out the sensor. For the purpose of minimization of losses of cooling liquid screw the new sensor as soon as possible.
|
|
Address with the eats sensor as it is possible more carefully as its damage is capable to make appreciable impact on power supply system functioning as a whole. |
3. Installation is made upside-down. In summary check level of cooling liquid, in case of need make the corresponding adjustment (see. Head Routine maintenance). |
|
|
|
