Honda Civic/Acura Integra

since 1994 of release

Repair and car operation


Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
- Control systems of the engine
   Specifications
   System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions
   Removal and installation RSM/ESM
   Check of serviceability of a condition and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a condition and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a condition and replacement of the sensor of temperature of soaked-up air (IAT)
   Check of serviceability of a condition and replacement of the sensor of temperature of cooling liquid of the engine (eats)
   Check of serviceability of a condition and replacement of the sensor of VMT/provision of cranked shaft/position of pistons in cylinders of the engine (TDC/CKP/CYP)
   Check of serviceability of a condition and replacement of the sensor of fluctuations of a cranked shaft (CKF)
   Check of serviceability of a condition and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a condition and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a condition and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a condition and replacement of the sensor of a detonation
   Check of serviceability of a condition and replacement of the sensor of speed of movement of the car (VSS)
   System of stabilization of turns of idling - the general information, check of a condition and IAC valve replacement
   Check of serviceability of a condition and replacement of the thermosensitive valve of turns of fast idling (FIT)
   System of a perepuskaniye of soaked-up air - the general information, check of a condition and replacement of a diaphragm of the IAB valve
   System of operated ventilation of a case (PCV)
   System of a retsirkulyatsiya of the fulfilled gases (EGR) - the general information, check of a condition and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a condition and replacement of components
   The catalytic converter - the general information, check of a condition and replacement
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




94e743ed

Check of serviceability of a condition and replacement of the sensor of VMT/provision of cranked shaft/position of pistons in cylinders of the engine (TDC/CKP/CYP)

On considered models the sensor of provision of a cranked shaft structurally consists of three parts tracing, respectively, actually the provision of a shaft, position VMT of the engine (TDC sensor) and position of the piston of the cylinder No. 1 (CYP sensor). On the basis of the data arriving from the SKR sensor, ESM/RSM defines the moments of injection of fuel and ignition in each of engine cylinders, in parallel the sensor delivers information on frequency of rotation of the engine on the management module. The correct installation of a corner of an advancing of ignition is determined by signals of the TDC sensor at engine start. The CYP sensor informs the management module on readiness of each of cylinders for fuel injection in it. All three sensors are incorporated in uniform assembly which is established in the ignition distributor. Diagnostics of malfunctions of sensors is made by means of the input reader of data of memory ESM/RSM (see. System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions) and resistance measurements between the corresponding plugs of the socket of electroconducting of assembly.

SKRB sensor

 PERFORMANCE ORDER

1. For check of the SKR sensor disunite the electric socket on the distributor of ignition and measure resistance between plugs 2 and 6 in it (see an accompanying illustration). Compare result of measurement to requirements of Specifications.

2. Check plugs 2 and 6 on conductivity existence on weight – conductivity SHOULD not be, otherwise replace distributor assembly (see. Head engine Electric equipment).
3. If to reveal causes of infringement it is not possible, drive away the car on car repair shop for more detailed diagnostics.

TDC sensor

 PERFORMANCE ORDER

1. For check of the sensor disunite the electric socket on the distributor of ignition and measure resistance between plugs 3 and 7 in it (see an illustration above). Compare results of measurement to requirements of Specifications.
2. Check plugs 3 and 7 on conductivity existence on weight – conductivity SHOULD not be, otherwise replace distributor assembly (see. Head engine Electric equipment).
3. If to reveal causes of infringement it is not possible, drive away the car on car repair shop for more detailed diagnostics.

CYP sensor

 PERFORMANCE ORDER

1. For check of the sensor disunite the electric socket on the distributor of ignition and measure resistance between plugs 4 and 8 in it (see an illustration above). Compare results of measurement to requirements of Specifications.
2. Check plugs 4 and 8 on conductivity existence on weight – conductivity SHOULD not be, otherwise replace distributor assembly (see. Head engine Electric equipment).
3. If to reveal causes of infringement it is not possible, drive away the car on car repair shop for more detailed diagnostics.