Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
- Power supply system and release
Specifications
Sbrasyvaniye of pressure in a power supply system
Check of serviceability of functioning of fuel pump/pressure of fuel
Check of a condition and replacement of fuel lines and their shtutserny connections
Removal and installation of the fuel pump
Check of a condition and replacement of the sensor of fuel consumption
Removal and installation of a fuel tank
Cleaning and repair of a fuel tank - general information
Removal and installation of assembly of an air purifier
Removal, installation and adjustment of a cable of an accelerator
System of electronic injection of fuel (EFI) - the general information
Check of serviceability of functioning of system of injection
Removal and installation of the case of a throttle
Removal and installation of a regulator of pressure of fuel
Removal and installation of the fuel highway and injectors of fuel of injectors of fuel
Release system - the general information
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Check of a condition and replacement of fuel lines and their shtutserny connections
|
|
1. Before starting service of fuel lines or their shtutserny connections it is necessary to dump pressure in a power supply system (see Sbrasyvaniye pressure in a power supply system).
2. Lines of a fuel path of a power supply system are laid between a fuel tank and an impellent compartment. Steel tubes and flexible fuel hoses fasten to the car bottom by means of clips and screw fixture. Each time when the car rises over the earth with any purpose (for example, for survey or replacement of components of system of production of the fulfilled gases), try to use a case and to check a condition of fuel lines and their shtutserny connections. Attentively examine all hoses and tubes of a fuel path on existence of cracks, twisting, deformations and other damages.
3. At identification of signs of internal pollution or passableness violation the corresponding section of a fuel path is necessary for removing and blowing the compressed air. Without fail check also a condition of the mesh filter of the sensor of fuel consumption (see. Removal and installation of the fuel pump). |
|
Steel tubes
|
|
1. Use as replaceable sections only high-strength steel tubes of known producers.
2. Remember that copper and aluminum tubes are not capable to sustain vibrating loadings arising in use the car.
3. Do not forget that fuel lines on the models equipped with system of injection, should maintain high internal pressure.
4. Often in firm shops of automobile accessories it is possible to get the sections of metal tubes equipped with carving shtutserny nozzles. During the easing and a tightening of shtutserny connections use two wrenches to avoid a provorachivaniye of a reciprocal part of the socket. Without fail check a condition of shtutserny connections of sealing rings used for sealing. The worn-out or mechanically damaged rings at once replace. Try to use as replaceable components only firm details. |
|
Flexible hoses
|
|
At replacement of fuel hoses use only firm components calculated on high internal pressure. |
|
|
|
|
1. Flexible fuel hoses should be laid not closer than in 10 cm from components of system of production of the fulfilled gases and is not closer than in 25 cm from the catalytic converter. Watch, that fuel lines did not adjoin to body elements and suspension bracket components (see an accompanying illustration). The minimum admissible size of a gap makes 6.3 mm. |
|
|
Removal and installation
|
|
1. Dump pressure in a power supply system (see Sbrasyvaniye pressure in a power supply system).
2. Liberate section of a fuel path subject to dismantle from intermediate clamps of fastening it to the car bottom.
3. Release collars of fastening of rubber hoses to steel tubes of a fuel path. For a hose detachment повращайте it on a tube.
|
|
4a. Installation is made upside-down. Do not forget to replace sealing rings of carving shtutserny connections. |
|
|
4b. Sealing washers of a hollow bolt of shtutserny knot on the fuel filter also are subject to replacement without fail (see accompanying illustrations). |
|
|
Repair The damaged sections of fuel lines (tubes or hoses) should be removed and replaced new, firm production. |
|
