Honda Civic/Acura Integra

since 1994 of release

Repair and car operation

Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
- Engine electric equipment
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information
   Check of functioning of system of ignition
   Check of a condition and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management with ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation and adjustment of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Replacement of a regulator of tension and generator brushes
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and starter installation
   Removal and installation of the traction relay
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment

94e743ed Проститутки Кронштадского района в Питере на

Check of installation and adjustment of a corner of an advancing of ignition

Procedure described below is applicable to the majority of models of cars considered in the real Management. However, if VECI given on a label data differ from stated below, follow the instructions VECI.


1. Start the engine and warm up it to normal working temperature.

2. At the switched-off ignition find under a cowl a label of VECI and attentively familiarize with the instructions stated in it on укам a corner of an advancing of ignition. Special value has correctness of installation of turns of idling as frequency of rotation of the engine is directly connected with a corner of an advancing of ignition. Prepare all necessary tools (see an accompanying illustration):
   1. Vacuum jams – All disconnected vacuum hoses should be corked immediately. For this purpose jams of the various size and a configuration are issued.
   2. The stroboscope with inductive connection - Provides a pulsation of the bright, ostronapravlenny beam synchronized with the moments of an iskroobrazovaniye on electrodes of a spark plug of the first cylinder. It is connected to VV to a wire of a candle of the first cylinder in compliance by instructions of manufacturers.
   3. The special wrench – On some models access to a clamping bolt of the distributor is limited and its otdavaniye with application of a key of a usual form becomes the extremely inconvenient.

3. At the switched-off ignition, according to instructions of manufacturers connect a stroboscope. A food on a stroboscope usually moves from the onboard storage battery. The reception inductive sensor of a lamp is established on VV a wire of a spark plug of the first cylinder (on all models counting of cylinders begins from a driving belt).

4. Find adjusting distributive labels on a forward cover and a pulley of a cranked shaft (see an accompanying illustration).

5. Find the 2-contact service socket under an overlay of a threshold of a forward passenger door of the car (see an accompanying illustration). At the switched-off ignition connect among themselves socket contacts by a wire crossing point.

6. Start the heated-up engine to normal working temperature and direct a stroboscope beam on the index on a forward cover of the engine.
7. Corresponding (see VECI label) from highlighted by a beam of a stroboscope of labels of a pulley of a cranked shaft, remaining motionless, it should appear combined with the index on a cover.
8. In case of need weaken three fixing bolts and correct position of the case of the distributor, achieving the correct combination of labels.
9. Tighten bolts and repeat check. Make sure that turns of idling of the engine did not change.
10. Muffle the engine and remove a stroboscope.
11. Establish into place a viewing stopper and remove a wire crossing point from the service socket.