Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
- Engine electric equipment
   Specifications
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information
   Check of functioning of system of ignition
   Check of a condition and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management with ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation and adjustment of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Replacement of a regulator of tension and generator brushes
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and starter installation
   Removal and installation of the traction relay
+ Control systems of the engine
+ gear shifting Box
+ Cцепление and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and installation of the distributor of ignition

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


2. Mark wires and hoses and disconnect from the distributor electroconducting and hoses.
3. Find on a distributor cover a convex label (in the form of figure or a letter), indicating location of the VV plug of a wire of a spark plug of the first cylinder. If the cover is not equipped with this sort of marking, find the plug, having walked to it on a wire from a candle of the first cylinder, and put down the corresponding label independently.
4. Uncover the distributor (see. Head Routine maintenance) also turn a cranked shaft so that the begunok was developed by a nouse towards an arrangement of the plug of a candle wire of the first cylinder (see. Engine repair without extraction from the car - the Civic models or engine Repair without extraction from the car - the Integra models).

5a. Put on edge of the case of the distributor, directly opposite to a nouse a begunka parallel to an axis of the last, an oriyentatsionny label (if the begunok has some nouses, choose central). Mark also landing provision of the basis of the distributor the engine (see accompanying illustrations). Bolts of fastening of the distributor on the Civivc models.

5b. Bolts of fastening of the distributor on the Integra models.

6. Give clamping a bolt (ы) and take the distributor from the engine, having pulled it strictly vertically up.

In order to avoid data to zero of efforts on drawing of adjusting labels, do not allow a provorachivaniye of a cranked shaft after extraction of the distributor of ignition from the engine!

Installation

If the provorachivaniye of a cranked shaft was allowed at the distributor of ignition taken from the engine, it is necessary to bring the engine into position VMT of the first cylinder (see. The appropriate section in engine Repair without extraction from the car - the Civic models or engine Repair without extraction from the car - the Integra models and at installation of the distributor to achieve the relevant situation it a begunka.


 PERFORMANCE ORDER

1. Put on the distributor case a new sealing ring.
2. Accurately fill the distributor in a reception nest in a head of cylinders. Achieve combination of the landing labels put in the course of dismantle.

Ledges at an end face of a shaft of the distributor and reciprocal grooves in an end face of a camshaft have an asymmetric arrangement that brings to naught possibility of installation of the distributor with a turn on 180 °.


3. If it is not possible to plant completely the distributor, first of all make sure of correctness of combination of landing labels, then achieve, that the begunok was developed by a nouse precisely towards a label on the brink of the case.
4. Freely screw clamping a bolt (ы).
5. Further assembly make as it should be, the return to a dismantle order. Check installation of a corner of an advancing of ignition, then strongly tighten clamping a bolt of fastening of the distributor on the engine.