Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
- Engine electric equipment
   Specifications
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information
   Check of functioning of system of ignition
   Check of a condition and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management with ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation and adjustment of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Replacement of a regulator of tension and generator brushes
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and starter installation
   Removal and installation of the traction relay
+ Control systems of the engine
+ gear shifting Box
+ Cцепление and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Check of serviceability of functioning and replacement of the module of management with ignition (ICM)

Check

 PERFORMANCE ORDER

1. Check serviceability of giving of a food on the ignition module. Uncover also a begunok of the distributor and disconnect from ICM a black and yellow wire (see an accompanying illustration). Make sure available tension of the battery directly on the electroconducting socket at the included ignition (a key in the situation ON, the engine is not started).

2. Check a condition of a contour of ignition and accompanying components. If tension on ICM is absent, check an electroconducting condition on a chain site between the module and the battery (see. Head Onboard electric equipment). First of all always it is necessary to check a condition of safety locks of switches of ignition of No. No. 41 (80 And on the Civic models and 100 And on the Integra models) and 42 (40 And) in the assembly block of relays/safety locks located under a cowl. Also check a safety lock No. 9 (15 And) in the assembly block in car salon. Attentively investigate an electric contour and make sure that the switch of ignition provides food giving on ICM at key turn in the situation ON. Also check a flavovirent wire between ICM and the module of management in capacity (RSM) and the dark blue wire connected to a tachometer, or its service socket. If conductivity between the ends any of the mentioned wires is absent, therefore takes place break and the corresponding electroconducting it is necessary to replace. If conductivity between one of the ends of a wire and weight takes place, short circuit (for more details see schemes of electric connections in Head Onboard electric equipment) therefore takes place.

3. Make sure of serviceability of giving of a food from the ignition coil to ICM. At the included ignition (do not start the engine) make sure available tension between dark blue (Hitachi distributor) / white-dark blue (TES distributor) and mass of a body (see an accompanying illustration). Tension should equal developed by the battery.

4. If tension is absent, check a chain on a site between the corresponding wire and the coil. Also check coil windings on existence of internal breaks (see. Check of a condition and replacement of the coil of ignition).
5. If the coil and chain electroconducting as it should be, and an iskroobrazovaniye is absent, replace ICM.

Replacement

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


2. Uncover and, at the corresponding complete set, the distributor filter (see. Head Routine maintenance).
3. Disunite all electric sockets on ICM.

4. Turn out the fixing screw (ы) and take ICM from the ignition distributor (see an accompanying illustration).

5. Installation is made upside-down