Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   General information and precautionary measures
   Search of causes of failures of electric equipment
   Safety locks - the general information
   Chain breakers
   The relay - the general information and check of serviceability of functioning
   Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
   Check of serviceability of functioning and replacement of podrulevy switches
   Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column
   Check of serviceability of functioning and replacement of switches of the dashboard
   Check of serviceability of functioning of measuring instruments of a combination of devices
   Removal and installation of a combination of devices
   Removal and installation of a radio receiver and loudspeakers
   Removal and installation of the aerial of a radio receiver
   Replacement of lamps of head headlights
   Adjustment of the direction of optical axes of head headlights
   Replacement of block headlights
   Replacement of lamps
   Running fires of light time of day (DRL)
   Check of serviceability of functioning and replacement of the electromotor of a drive of screen wipers
   Check of serviceability of functioning and replacement of a horn of a horn
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   Control system of speed (темпостат) - general information and check of serviceability of functioning
   The electric drive of window regulators - general information and check of serviceability of functioning
   The uniform lock - general information and check of serviceability of functioning
   The electric drive of external rear-view mirrors - general information and check of serviceability of functioning
   Safety cushions - the general information
   + Schemes of electric connections - the general information




94e743ed

Check of serviceability of functioning and replacement of the switch of ignition and lock of blocking of a steering column

Considered in the real Management of the car are equipped with safety cushions (SRS). At performance of any works near sensors of blows, a steering column or the dashboard disconnect SRS (see. Safety cushions - the general information). Do not make check of the SRS models by means of any type of the diagnostic equipment.

Ignition switch

 PERFORMANCE ORDER

1. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


2. Remove the bottom section of the dashboard and casings of a steering column (see. Head Body).

3. Moving on a plait of electroconducting of the switch down along a steering column to the assembly block, disunite electric sockets (see accompanying illustrations).

4. Check conductivity existence between switch plugs (see the table below).
5. At identification of violations in distribution of conductivity replace the switch.
6. Insert a key into the lock and turn it in the situation LOCK (Blocking).

7. Turn out two fixing screws and remove the switch from a steering column (see an accompanying illustration).

8. Installation is made upside-down.

Card of conditions of the switch of ignition

POSITION OF THE SWITCH

CONDUCTIVITY EXISTENCE BETWEEN PLUGS

Lay situation (ASS)

   Civic

3 and 8

   Integra

3 and 11

Incl. (ON)

   Civic

3, 8, 10 and 12

   Integra

3, 8, 9 and 11

Start (START)

   Civic

1, 3 and 12

   Integra

1, 3 and 8

Cylinder and assembly of the lock of blocking of a steering column

 PERFORMANCE ORDER

1. Turning the cylinder in all from the provided provisions, estimate degree of its wear on size люфта. The provision of a key in the lock should correspond the assembly put on the case to marking. In case of malfunction of the cylinder all zamkovy assembly is subject to replacement.
2. Disconnect from the battery at first a negative wire, then positive.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


3. Remove a casing of a steering column and the bottom section of the dashboard (see. Head Body).
4. Remove the ignition switch (see above).
5. Give fixing nuts and lower a steering column.

6. Assembly of the lock is fixed in a column by a collar, drawn by two screws with srezny heads (see an accompanying illustration). To Nakernita of a head of screws, then drill them (use a drill on 4.8 mm). Throw off a collar and remove lock assembly from a steering column.

7. Without inserting a key, put the replaceable lock on a regular place and fix it bolts with nuts. Tighten nuts of fastening of a steering column to a dashboard flange with effort of 12.2 Nanometers. Coupling bolts of the fixing plug are tightened with effort of 22 Nanometers.
8. Establish into place the ignition switch, and also sections of the dashboard and a casing of a steering column.
9. Connect to the battery at first a positive wire, then negative.