The device, service, Honda Civic and Acura Integra repair - Removal and installation of the pallet of a case of the engine//since 1994 of release / newmediawave.ru

Honda Civic/Acura Integra

since 1994 of release

Repair and car operation



Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
- Engine
   - Engine repair without extraction from the car - the Civic models
      General information
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of a cover of a head of cylinders
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
      VTEC systems - the general information and check of a condition of components
      Removal, check of a condition and installation of assembly of yokes
      Replacement of klapanny springs with plates and maslootrazhatelny caps
      Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Replacement of a forward epiploon of a cranked shaft
      Removal, check of a condition and camshaft installation
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and flywheel installation / driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit
   + engine Repair without extraction from the car - the Integra models
   + General and major maintenance of the engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ Cцепление and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


самовывоз металлолома




Removal and installation of the pallet of a case of the engine

 Removal

 PERFORMANCE ORDER

1. Warm up the engine to normal working temperature, then merge from it engine oil and remove the oil filter (see. Head Routine maintenance).
2. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!


3. To Poddomkratta the car also establish it on props. Remove protection of a case.

4. Turn out bolts of fastening of the pallet to the engine block (see an accompanying illustration).

5. Обстучав the pallet on perimeter a hammer with soft brisk for the purpose of destruction of a layer of hermetic, separate it from the block (at all do not make attempts to hook the pallet under an interfaced surface).
6. Scratch out from interfaced surfaces of the pallet and the block all traces of hermetic and a material of old laying. Remove from the pallet or the block face sealing inserts. Carefully wipe interfaced surfaces the rags moistened in acetone. Clean and dry carving openings in the block.

Installation

 PERFORMANCE ORDER

1. Wash out the pallet solvent and carefully dry it. Make sure of absence of deformations of an adjusting flange of the pallet, in case of need lay the pallet a flange on the flat wooden block and make a rikhtovka.
2. Impose on a prokladochny surface of a flange of the pallet a RTV hermetic pillow in thickness of 3 mm. Track, that hermetic was imposed from the interior of boltovy openings.
3. Accurately press the pallet to the block. Screw bolts and, moving on a spiral from the center outside, in stages (on 1/4 turns for an approach) tighten them with demanded effort (see. Specifications). Remember that pulling of fixture is fraught with development of leaks.
4. Fill in engine oil (see. Head Routine maintenance), start the engine and check the pallet on existence of leaks.