Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
- Engine
- Engine repair without extraction from the car - the Civic models
General information
Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
Removal and installation of a cover of a head of cylinders
Removal and installation of the inlet pipeline
Removal and installation of a final collector
VTEC systems - the general information and check of a condition of components
Removal, check of a condition and installation of assembly of yokes
Replacement of klapanny springs with plates and maslootrazhatelny caps
Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
Replacement of a forward epiploon of a cranked shaft
Removal, check of a condition and camshaft installation
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a condition and installation of the oil pump
Removal and flywheel installation / driving disk
Replacement of a back epiploon of a cranked shaft
Check of a condition and replacement of support of a suspension bracket of the power unit
+ engine Repair without extraction from the car - the Integra models
+ General and major maintenance of the engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, check of a condition and installation of assembly of yokes
|
|
Covers of bearings of a camshaft act in film together with assembly of yokes. In order to avoid a camshaft vyskakivaniye under the influence of effort of a tension of a gas-distributing belt, ask the assistant to hold a shaft and at once establish into place a cover of the extreme bearing (it is supposed that the belt of a drive of GRM does not act in film). Having removed covers of bearings of a camshaft, attentively check a condition both bearings, and their necks on a shaft (see. Removal, check of a condition and camshaft installation). |
Removal
Check
|
|
|
1. Having removed assembly of yokes, it will be reasonable to disassemble it for the purpose of more detailed studying of a condition of components. Turn out fixing bolts and remove from axes of a yoke, a spring and a cover of bearings.
|
|
On the engines equipped with VTEC system, it will be reasonable to fasten yokes of primary and secondary inlet valves rubber bandages. Mark the provision of axes of yokes in relation to covers of bearings. Try to put removed components as their installation as at assembly they should be planted strictly on the former places. |
|
|
2. Carefully clear components and check them on existence of signs of wear and damages. Estimate a condition of surfaces of yokes contacting to a camshaft (see an accompanying illustration). Check on existence задиров and signs of excessive wear of a surface of landing of yokes on axes, and also walls of landing nests of yokes. Defective components are subject to replacement. Make sure also of passableness маслотоков. |
3. Blow a masloraspylitel. |
|
Installation
|
|
1. Grease all components with pure impellent oil and establish them on the regular places on an axis of yokes.
|
|
Pay attention to the marking, distinguishing left foreign components from the right-hand. |
2. On the engines equipped with VTEC system, replace a sealing ring of a masloraspylitel, then establish the last on the regular place in a head of cylinders.
3. Grease cams and necks of a camshaft with special adjusting greasing. Put on interfaced to a head of cylinders of a surface of covers of the first and sixth bearings of a camshaft a thin layer of anaerobny hermetic then establish assembly of yokes on the regular place.
|
|
4. In stages in the correct order (see an accompanying illustration) tighten bolts of fastening of covers of a camshaft with demanded effort. |
5. Further installation of components is made as it should be, the return to an order of their dismantle. In summary do not forget to make adjustment of klapanny gaps (if in it there is a need) (see. Head Routine maintenance).
6. Start the engine and check it on existence of signs of leakages of oil and serviceability of functioning. |
|
|
|
