Honda Tsivik
+ Honda Civic and Acura Integra brand Cars
+ Maintenance instruction
+ Routine maintenance
- Engine
- Engine repair without extraction from the car - the Civic models
General information
Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
Removal and installation of a cover of a head of cylinders
Removal and installation of the inlet pipeline
Removal and installation of a final collector
VTEC systems - the general information and check of a condition of components
Removal, check of a condition and installation of assembly of yokes
Replacement of klapanny springs with plates and maslootrazhatelny caps
Removal, check of a condition and installation of a gas-distributing belt and cogwheels of a drive of GRM
Replacement of a forward epiploon of a cranked shaft
Removal, check of a condition and camshaft installation
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a condition and installation of the oil pump
Removal and flywheel installation / driving disk
Replacement of a back epiploon of a cranked shaft
Check of a condition and replacement of support of a suspension bracket of the power unit
+ engine Repair without extraction from the car - the Integra models
+ General and major maintenance of the engine
+ cooling and heating Systems
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ gear shifting Box
+ clutch and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal and installation of a cover of a head of cylinders Removal
|
|
1. Disconnect a negative wire from the battery.
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
2. Remove from a head of cylinders a cover of the distributor of ignition with VV connected to it wires. Disconnect wires from the plugs on a head of cylinders and its cover (see. Head Routine maintenance). Do not forget to mark a wire in order to avoid violation of an order of ignition at assembly.
3. Mark and disconnect from the case of a throttle and a cover of a head of cylinders all procedures of a wire stirring to performance and hoses.
4. Carefully wipe a cover in order to avoid garbage hit in a head cylinders/assembly of the klapanny mechanism.
5. Turn out bolts of fastening of a cover of a head of cylinders – act as it should be, the return specified in a picture (see an illustration below).
6. Accurately uncover together with sealing laying. If laying подлипла to an interfaced surface of a head, обстучите a cover a hammer with soft brisk for the purpose of destruction of a layer of hermetic. At all do not undertake attempts to separate a cover by a poddevaniye it the lever entered between interfaced surfaces. |
|
Installation
|
|
1. Separate old laying, then carefully smooth out interfaced surfaces of a head of cylinders and its cover. Having scratched out traces of old hermetic and laying fragments, wipe surfaces the rags moistened in acetone.
2. Impose a little RTV hermetic on corners where the interfaced surface of a head adjoins to assembly of yokes (see an accompanying illustration). Wait about five minutes, waiting the moment of the beginning of polymerization of hermetic.
|
|
Make sure that the top layer of hermetic slightly hardened, after it start cover installation (in the conditions of the increased humidity polymerization of hermetic can begin with a small delay). |
|
|
3. Fill cast laying in a flute going on perimeter of a cover. Plant in a cover isolating plugs through passage, having slightly greased them with solution of soap water. Lay a cover on a head, then screw fixing bolts and tighten them in that order (see an accompanying illustration) with demanded effort (see. Specifications). |
4. Further installation is made as it should be, the return to a removal order. Before connecting wire VV, make sure of reliability of landing of rubber sealants of spark plugs. |
|
|
|
